Registered Quality System ISO9001

Taizhou,Zhejiang,China

Material Safety Data Sheet

1. Chemical Product and Company Identification

Trade Name: Super Glue

Product Identifier: Cyanoacrylate Adhesive

Manufacturer Information

MSDS Prepared by:

Jiaojiang Shundebao Industry & Trade Co.,Ltd.

No.117-7 Xingxing Avenue,Taizhou,Zhejiang,China

For addition health,safety or regulatory information,call +86-576-8011306

2. Composition,Information on Ingredients

CAS No. Chemical Name Percentage by Weight ACGIH TWA Osha Pel Osha Stel

7085-85-0 ethyl-2-cyanoacrylate 60-100 n/e n/e n/e

9011-14-7 poly (methyl methacrylate) 10-30 n/e n/e n/e

123-31-9 hydroquinone 0-1 2mg/m3 2mg/m3 n/e

3. Hazards Identification

3.1 Emergency Overview

Appearance : Colorless liquid

Odor : Irritating

CAUTION!

May become unstable at high temperatures or may react with water.May be harmful if inhaled. May cause irritation of nose,throat and lungs.

Bonds skin instantly. Causes skin irritation.

Bonds eyelids instantly. Causes eye irritation.

HMIS Rating

HEALTH = 1 (moderate)

FLAMMABILITY = 2 (moderate)

REACTIVITY = 1 (slight)

2. Potential Health Effects

Immediate Hazards

INGESTION: No hazards known to company.

INHALATION: May be harmful if inhaled.Liquid or vapor may cause irritation of nose, throat and lungs.

SKIN: Bonds skin instantly. Causes irritation.

EYES: Bonds eyelids instantly. Irritates eyes,causes tearing from eye irritation.

4. First Aid Measures

INGESTION: If accidentally swallowed, dilute by drinking large quantities of water.Immediately contact poison control center or hospital emergency room for any other additional treatment directions.

INHALATION: If inhaled, remove to fresh air. If not breathing,give artificial respiration,

preferably mouth-to-mouth.Call a physician.

SKIN: If skin bonding occurs, soak in nail polish remover or acetone and carefully peel or

roll skin apart (do not pull).

EYES: If eye contact occurs, hold eyelid open and rinse thoroughly but gently with only

water for 15 minutes and GET MEDICAL ATTENTION. Do not use any solvents to

flush the eye and its surroundings. Liquid glue will sting eye

temporarily. Solidified glue may irritate eye like a grain of sand and should be

treated by an eye doctor.

5. Fire Fighting Measures

Autoignition Temperature: n/e

Upper/Lower Flammable Limits: Not available

Up/Lower Explosive Limits, % by Vol: Not available

Flash Point: 83 deg C (CC)

Keep away from heat and flame.

In case of fire, use water spray, dry chemical, foam or CO2. Use water to keep fire-expose containers cool.

6. Accidental Release Measures

Eliminate all ignition sources. Soak up with absorbent material and remove to a chemical disposal area. Prevent entry into natural bodies of water.

7. Handling and Storage

7.1 Handling

Handle in accordance with good industrial hygiene and safety practices. These practices include avoiding unnecessary exposure and removal of the material from eyes, skin and clothing.Wash thoroughly after handling. Always use appropriate Personal Protective Equipment (PPE).

INHALATION: Avoid breathing vapor. Use with adequate ventilation.

SKIN: Avoid contact with skin and clothing.

EYES: Avoid contact with eyes.

7.2 Storage

Keep away from amines.

Store in cool, dry area away from sun and heat.

Keep containers tightly closed.

Exposure to small amounts of moisture, even moisture in air, causespolymerization and renders the product unusable.

Keep away from heat, sparks, flame and other ignition sources.

8. Exposure Controls/Personal Protection

8.1 Exposure Controls

ENGINEERING CONTROLS: The following exposure control techniques may be used to effectively minimize employee exposure: local exhaust ventilation, enclosed system design, process isolation and remote control in combination with appropriate use of personal protective equipment and prudent work practices.These techniques may not necessarily address all issues pertaining to your operations. We, therefore, recommend that you consult with experts of your choice to determine whether or not your programs are adequate. If airborne contaminants are generated when the material is heated or handled, sufficient ventilation in volume and air flow patterns should be provided to keep air contaminant concentration levels below acceptable criteria.

8.2 Personal Protection

Where air contaminants can exceed acceptable criteria, use NIOSH/MSHA approved

respiratory protection equipment. Respirators should be selected based on the form and

concentration of contaminants in air in accordance with OSHA laws and regulations or other

applicable standards or guidelines, including ANSI standards regarding respiratory

protection.Use goggles if contact is likely.Wear impervious gloves as required to prevent

skin contact.

8.3 Exposure Guidelines

Ethyl 2-Cyanoacrylate 7085-85-0

ACGIH TLV: 2mg/m³ TWA

OSHA PEL: n/e

9. Physical and Chemical Properties

Percent Volatiles Not determined

pH @ 25 C Not available

Specific Gravity 1.05

Appearance Colorless liquid

Autoignition Temperature n/e

Boiling Point 62 deg C (5 mm Hg)

Vapor Density (Air=1) > 1

Vapor Pressure, mm Hg @ 20 C 0.13 (@ 20 deg C)

Evaporation Rate (Butyl Acetate=1) < 1

Upper/Lower Flammable Limits Not available

Up/Lower Explosive Limits, % by Vol Not available

Flash Point 83 deg C

Freezing Point < -20 deg C

Odor Irritating

Odor Threshold, ppm Not available

Solubility in Water Negligible

Coefficient of Water/Oil Distrib. Not applicable

10. Stability and Reactivity

Normally stable, but may become unstable at high temperatures or may react with water.

Conditions to Avoid: Exposure to heat, flame and incompatibles.

Incompatibilities: Water, alcohols, amines, bases and direct UV.

Decomposition products may include: Oxides of carbon.

Hazardous polymerization: Will not occur.

Other Hazards: None known to company.

11. Toxicological Information

See Section 3 Hazards Identification information.

Ethyl 2-Cyanoacrylate 7085-85-0

LC50: Not available

LD50: Not available

12. Ecological Information

Not determined.

13. Disposal Considerations

Recover free liquid. Absorb residue and dispose of according to local, state/provincial, and

federal requirements. Empty container: May contain explosive vapors. DO NOT cut,

puncture or weld on or nearby.

14. Transport Information

Ground: Not regulated

Air: Not regulated

Sea: Not regulated

15. Regulations Information

None

16. Other Information

Definitions: n/a=not applicable , n/e=not established

Disclaimer

SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, CONCERNING THE

PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE,

except that the product shall conform to contracted specifications, and that the product

does not infringe any valid United States or Canadian patent. No claim of any kind shall be

greater in amount than the purchase price of the quantity of product in respect of which

damages are claimed. In no event shall Seller be liable for incidental or consequential

damages, whether Buyer's claim is based on contract, breach of warranty, negligence or

otherwise.